Ford 2004 Focus v.1 Bedienungsanleitung

Introduction 4Instrument Cluster 10Warning and control lights 10Gauges 14Entertainment Systems 16AM/FM stereo cassette 16AM/FM stereo with CD 19Climat

WARNING LIGHTS AND CHIMESStandard instrument clusterOptional instrument cluster2.3L 14 PZEV instrument clusterWarning lights and gauges can alert you

• LATCH lower anchors are recommended for use by children up to22 kg (48 pounds) in a child restraint. Top tether anchors can be usedfor children up t

1. Position the child safety seat in aseat with a combination lap andshoulder belt.2. Pull down on the shoulder beltand then grasp the shoulder beltan

4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear

8. Allow the safety belt to retract toremove any slack in the belt.9. Before placing the child in theseat, forcibly move the seat forwardand back to m

1. Position the child safety seat on the seat cushion.2. Route the child safety seat tether strap over the back of the seat.On hatchbacks, the removab

5. Clip the tether strap to theanchor as shown.If the tether strap is clippedincorrectly, the child safetyseat may not be retained properlyin the even

LATCH anchors for child seatinstallation have been provided inyour vehicle at the following locations:The anchors on both sides of thecenter of the re

STARTINGPositions of the ignition1. LOCK, locks the steering wheel,automatic transaxle gearshift leverand allows key removal.2. OFF, shuts the engine

If you smell exhaust fumes inside your vehicle, have your dealerinspect your vehicle immediately. Do not drive if you smellexhaust fumes.Important saf

If starting a vehicle with a manualtransaxle:1. Make sure the parking brake isset.2. Push the clutch pedal to the floor.• Turn the key to 3 (ON) witho

Many lights will illuminate when you start your vehicle to make sure thebulb works. If any light remains on after starting the vehicle, have therespec

Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to illuminate, have the vehicle serviced.• If the driver’s safety

Guarding against exhaust fumesCarbon monoxide is present in exhaust fumes. Take precautions to avoidits dangerous effects.If you smell exhaust fumes i

effectiveness of the ABS and will increase your vehicle’s stoppingdistance. The ABS will be activated immediately, allowing you to retainfull steering

TRACTION CONTROL姟 (IF EQUIPPED)Your vehicle may be equipped with a Traction Control娂 system. Thissystem helps you maintain the stability and steerabil

If the power steering system breaks down (or if the engine is turnedoff), you can steer the vehicle manually, but it takes more effort.If the steering

4. Start the vehicle.If it is necessary to use the above procedure to move the gearshift lever,it is possible that a fuse has blown or the vehicle’s b

To put your vehicle in P (Park):• Come to a complete stop• Move the gearshift lever and securely latch it in P (Park)Always set the parking brake full

• To return to D (Overdrive), move the gearshift lever into the D(Overdrive) position.• Selecting 2 (Second) at higher speeds will cause the transaxle

3. Start the engine, then press the brake pedal and release the parkingbrake.4. Move the gearshift lever to the desired gear, then slowly release thec

3. Turn the ignition off.Do not park your vehicle in Neutral, it may move unexpectedlyand injure someone. Use 1 (First) gear and set the parking brake

Driving a vehicle with the brake system warning light on isdangerous. A significant decrease in braking performance mayoccur. It will take you longer

Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue loador king pin w

GVWR (Gross Vehicle WeightRating) – is the maximumallowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo).

10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheeltrailer), and driver only (68 kg [150 lbs]). Consult your dealership (orthe RV

Preparing to towUse the proper equipment for towing a trailer and make sure it isproperly attached to your vehicle. See your dealer or a reliable trai

• Consult your local motor vehicle speed regulations for towing a trailer.• To eliminate excessive shifting, use a lower gear. This will also assistin

In case of a roadside emergency with a disabled vehicle (without accessto wheel dollies, car hauling trailer or flatbed transport vehicle) yourvehicle

GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program

Canadian customers who require roadside assistance, call1–800–665–2006.If you need to arrange roadside assistance for yourself, Ford MotorCompany will

This switch is located in the frontpassenger’s footwell, behind the kickpanel access cover.To reset the switch:1. Turn the ignition OFF.2. Check the f

Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey ———3A Violet Vio

Overdrive off (if equipped):Illuminates when the overdrivefunction of the transaxle has beenturned off, refer to the Drivingchapter. If the light flas

The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel DescriptionR17 — Starter relayR18 – Rear intermittent r

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description33 20A Horn, Power seats (SVT only)34 20A Power sunroof35 7.5A Interior lam

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description61 7.5A PATS modules, Instrument cluster62 7.5A License plate lamp63 20A Po

To remove a fuse, use the fuse puller tool provided on the powerdistribution box cover.The high-current fuses are coded as follows:Fuse/RelayLocationF

Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription10 10A (2.0L engineonly)Battery voltage sensor1A (2.3L engineonly)11 30A Anti-lock Br

Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription64 40A Heater blower motorR1 — Ignition relayR2 — Air pump motor relay (2.3Lengine on

The use of tire sealants may damage your tires.Temporary spare tire informationThe temporary spare tire for your vehicle is labeled as such. It is sma

Tire change procedure1. Park on a level surface, activatehazard flashers and set the parkingbrake.When one of the front wheels is off the ground, the

4. On coupe models, unsnap andremove the access door (ifequipped) on the lower rockermolding (SVT only) to access theproper jacking points.5. Loosen e

6. The vehicle jacking points aredepicted on the yellow warning labelon the jack shown here. Dependingon which tire is to be changed,locate the jack a

High beams: Illuminates when thehigh beam headlamps are turned on.Key-in-ignition warning chime: Sounds when the key is left in theignition in the OFF

Do not attempt to push-start your vehicle. Automatictransmissions do not have push-start capability; doing so maydamage the catalytic converter.Prepar

2. Connect the other end of the positive (+) cable to the positive (+)terminal of the assisting battery.3. Connect the negative (-) cable to the negat

4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarbureto

• 2.0L SPI engine• 2.0L Zetec engine2004 Focus (foc)Owners Guide (post-2002-fmt)USA English (fus)Roadside Emergencies143

5. Ensure that the cables are clear of fan blades, belts, moving parts ofboth engines, or any fuel delivery system parts.Jump starting1. Start the eng

2. Remove the jumper cable on the negative (-) connection of thebooster vehicle’s battery.3. Remove the jumper cable from the positive (+) terminal of

4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery.After the disabled vehicle has been started and the jumper

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handli

In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo

the red section and the multi-function warning light illuminates, refer toHow fail safe cooling works in coolant in the Maintenance andSpecifications

In the United States, a warranty dispute must be submitted to theDispute Settlement Board before taking action under the Magnuson-MossWarranty Act, or

The Dispute Settlement Board may not be available in all states. FordMotor Company reserves the right to change eligibility limitations, modifyprocedu

from Ford and Lincoln Mercury dealership management, recognized fortheir business leadership qualities.What the Board needsTo have your case reviewed

Making a decisionBoard members review all available information related to eachcomplaint, including oral presentations, and arrive at a fair and impar

In the CAMVAP program, impartial third-party arbitrators conducthearings at mutually convenient times and places in an informalenvironment. These impa

ORDERING ADDITIONAL OWNER’S LITERATURETo order the publications in this portfolio, contact Helm, Incorporated at:HELM, INCORPORATEDP.O. Box 07150Detro

3. The vehicle is out of service for repair of nonconformities for a total ofmore than 30 calendar days (not necessarily all at one time)In the case o

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is

PAINT CHIPSYour dealer has touch-up paint and sprays to match your vehicle’s color.Take your color code (printed on a sticker in the driver’s door jam

• Spray Motorcraft Engine Shampoo and Degreaser (ZC-20) on all partsthat require cleaning and pressure rinse clean.• Never wash or rinse the engine wh

AM/FM STEREO WITH CASSETTE (IF EQUIPPED)1. Cassette door: Insert the cassette with the opening to the right.2. Rewind/fast forward: Press toreverse/ad

• 2.0L Zetec-E engine• 2.3L engine2004 Focus (foc)Owners Guide (post-2002-fmt)USA English (fus)Cleaning160

PLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your dealer.• For routine clea

INTERIORFor fabric, carpets, cloth seats, safety belts and seats equipped with sideair bags:• Remove dust and loose dirt with a vacuum cleaner.• Remov

FORD, LINCOLN AND MERCURY CAR CARE PRODUCTSYour Ford, Lincoln or Mercury dealer has many quality products availableto clean your vehicle and protect i

SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide a

• Manual transmission:1. Set the parking brake, depress the clutch and place the gearshift in N(Neutral).2. Block the wheels.Note: Do not start your e

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT2.0L I4 SPI1. Power steering fluid reservoir2. Engine oil dipstick3. Engine oil filler cap4. Brake/Clu

2.0L Zetec-E Engine1. Power steering fluid reservoir2. Engine oil filler cap3. Brake/Clutch fluid reservoir4. Power distribution box5. Air filter asse

2.3L I4 PZEV Engine1. Power steering fluid reservoir2. Engine oil filler cap3. Brake/Clutch fluid reservoir4. Power distribution box5. Battery6. Winds

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

5. Menu: Press MENU to accessmain menu functions. UseSEEK/ for adjustments.Tune adjust: Press MENU until MAN appears in the display. Pressor to manual

5. Locate and carefully remove the engine oil indicator (dipstick).• 2.0L SPI/2.3L I4engine• 2.0L Zetec engine6. Wipe the indicator clean. Insert the

• 2.0L Zetec• 2.3L I4• If the oil level is below the MIN/ADD mark, add enough oil to raise thelevel within the MIN-MAX/ADD-FULL range.• Oil levels abo

3. Recheck the engine oil level. Make sure the oil level is not above theMAX mark on the engine oil level indicator (dipstick).4. Install the indicato

BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.How

When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps,resulting in personal injury a

If the battery has been disconnected or a new battery has been installed,the clock and the preset radio stations must be reset once the battery isreco

When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the “cold fill level” or within the “c

• Add Motorcraft Premium Gold Engine Coolant(yellow-colored), VC-7–A (U.S., except CA and OR), VC-7–B(CA and OR only), meeting Ford SpecificationWSS-M

2. When the engine is cool, wrap a thick cloth around the coolantpressure relief cap on the coolant reservoir (a translucent plastic bottle).Slowly tu

• NEVER increase the coolant concentration above 60%.• Increased engine coolant concentrations above 60% willdecrease the overheat protection characte

Press the security release control and remove the front panel. Toreposition the panel, insert the right-hand edge first, then the left-handside, until

When this occurs the vehicle will still operate. However:• The engine power will be limited.• The air conditioning system will be disabled.Continued o

The fuel system may be under pressure. If the fuel filler cap isventing vapor or if you hear a hissing sound, wait until it stopsbefore completely rem

clothing and wash skin thoroughly with soap and water. Repeated orprolonged skin contact with fuel liquid or vapor causes skin irritation.• Be particu

If the “Service Engine Soon/Check Engine” indicator comes on and stayson after you start the engine, the fuel filler cap may not be properlyinstalled.

Fuel qualityIf you are experiencing starting, rough idle or hesitation driveabilityproblems during a cold start, try a different brand of unleaded gas

ESSENTIALS OF GOOD FUEL ECONOMYMeasuring techniquesYour best source of information about actual fuel economy is you, thedriver. You must gather inform

2. Each time you fill the tank, record the amount of fuel added (in litersor gallons).3. After at least three to five tank fill-ups, fill the fuel tan

• Warming up a vehicle on cold mornings is not required and mayreduce fuel economy.• Resting your foot on the brake pedal while driving may reduce fue

It is important to note the box in the lower left corner of the windowsticker. These numbers represent the Range of L/100 km (MPG)expected on the vehi

sells, leases, trades vehicles, or supervises a fleet of vehicles are notpermitted to intentionally remove an emission control device or preventit fro

AM/FM STEREO WITH CD PLAYER (IF EQUIPPED)1. CD door: Insert the CD label side up.2. CD: Press to engage CD mode.CDs and tracks are selected andplayed

condition. To ready the on-board diagnostics system for I/M testing, aminimum of 30 minutes of city and highway driving is necessary asdescribed below

The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the “MIN” and“MAX” lines

operated for an extended period at high speeds, in city trafficduring hot weather or pulling a trailer, the vehicle should beturned off for about 30 m

High fluid levelFluid levels above the safe rangemay result in transaxle failure. Anoverfill condition of transmissionfluid may cause shift and/orenga

Checking and adding manual transmission fluid (if equipped)1. Clean the filler plug.2. Remove the filler plug andinspect the fluid level.3. Fluid leve

TreadwearThe treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernmen

TIRESTires are designed to give many thousands of miles of service, but theymust be maintained in order to get the maximum benefit from them.Glossary

Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (

Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - km/h (mph)Q 159 km/h (99 mp

12. Treadwear, Traction and Temperature Grades• Treadwear: The treadwear grade is a comparative rating based on thewear rate of the tire when tested u

Seating and Safety Restraints 71Seating 71Safety restraints 76Air bags 89Child restraints 95Driving 107Starting 107Brakes 111Traction control 113Trans

Audio distortion reduction (CLIP): Press and hold MENU until thedisplay changes. Then, press MENU until the CLIP menu displays. PressSEEK to engage/di

Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation than those of “P” typetires; t

Information on “T” type tiresT145/80D16 is an example of a tiresize.Note: The temporary tire size foryour vehicle may be different thanthis example.1.

Use the recommended cold inflation pressure for optimum tireperformance and wear. Under-inflation or over-inflation may causeuneven treadwear patterns

6. Visually inspect the tires to make sure there are no nails or otherobjects embedded that could poke a hole in the tire and cause an airleak.7. Chec

• Front Wheel Drive (FWD)vehicles (front tires at top ofdiagram)• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive (4WD)vehicles (front tires at top of

Sometimes irregular tire wear can be corrected by rotating the tires.Note: If your tires show uneven wear ask a qualified technician at aFord or Linco

Safety practicesDriving habits have a great deal to do with your tire mileage and safety.• Observe posted speed limits• Avoid fast starts, stops and t

Vehicles with Traction Control (if equipped) may exhibit some unusualdriving characteristics, when using snow chains, which can be avoided byswitching

For PCV valve replacement, see your dealer or a qualified servicetechnician. Refer to the scheduled maintenance guide for the appropriateintervals for

Fluid Ford PartNameApplication CapacityEngine oil(includes filterchange)4Motorcraft SAE5W-20 PremiumSynthetic BlendMotor Oil (US)Motorcraft SAE5W-20 S

Replacement panels: Your Ford Dealer will require the following if youneed to order a replacement panel:• Your name and address.• The vehicle identifi

Some transmission fluids may be labeled as dual usage, such asMERCON威 and MERCON威 V. These dual usage fluids are not to be usedin an automatic transmi

ItemFord PartName orEquivalentFord PartNumberFordSpecificationAutomatictransaxleMotorcraftMERCON威 VATFXT-5-QM MERCON威 VManual transaxle Motorcraft Ful

ENGINE DATAEngine2.0L SPIengine2.0L Zetec Eengine2.3L I4 engineCubic inches 121 121 138Required fuel 87 octane 87 octane 87 octaneFiring order 1–3–4–2

• Sedan2004 Focus (foc)Owners Guide (post-2002-fmt)USA English (fus)Maintenance and Specifications213

• Coupe2004 Focus (foc)Owners Guide (post-2002-fmt)USA English (fus)Maintenance and Specifications214

• WagonIDENTIFYING YOUR VEHICLECertification labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Certification label be a

Vehicle identification number (VIN)The vehicle identification number isattached to a metal tag and islocated on the driver sideinstrument panel. (Plea

Transmission/Transaxle code designationsYou can find a transmission/transaxle code on the vehicle certificationlabel which is located on the door pill

Code Transmission DescriptionElectricH One speed electricD Automatic 5–speed overdrive (5R44E)R Automatic 5–speed overdrive (5R55S)Passenger car appli

GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford

6006 AM/FM SOUND SYSTEM WITH 6–DISC IN DASH CHANGER(IF EQUIPPED)2004 Focus (foc)Owners Guide (post-2002-fmt)USA English (fus)Entertainment Systems22

Electrochromic compass mirrorElectrochromic compass mirror with outside temperatureEngine block heaterRemote startSmoker’s packTravel equipmentAutomat

Side window deflectorSpoilersFor maximum vehicle performance, keep the following information inmind when adding accessories or equipment to your vehic

AAir bag supplemental restraintsystem ...89–90, 93and child safety seats ...91description ...

Clutchfluid ...190–191operation while driving ...117recommended shift speeds ...118Coolantchecking and adding .

choosing the right fuel ...183comparisons with EPA fueleconomy estimates ...187detergent in fuel ...184filling

MManual transaxlelubricant specifications ...212Manual transmission ...117fluid capacities ...208reverse ...

TTemperature control(see Climate control) ...34Tilt steering wheel ...51Tires ...194–

227

228

229

9006 AM/FM SOUND SYSTEM WITH 6–DISC IN DASH CHANGER(IF EQUIPPED)1. CD Door: Insert the disc withthe playing side down and printedside up.2. Load: Pres

230

231

232

CD eject during playback: Press the eject control during CD playbackto eject the CD. Press again to cancel the eject process. To eject anotherdisc, pr

8. Bass: Press BASS to adjust thebass levels. Turn the volume controlto decrease/increase the bassoutput.Treble: Press to adjust the treblelevels. Tur

11. Scan: Press SCAN to move upthe radio frequency band. SCANautomatically finds a station, plays itfor five seconds, then moves to the next station.

IN-DASH CD/MP3 SOUND SYSTEM (IF EQUIPPED)1. CD door: Insert a CD or MP3label side up.2. Soft keys: Press to make various selections in the audio menus

Press again for a brief sampling of all MP3 directories on the disc. SCANALL appears at the bottom of the display.6. Shuffle: CD/CD changer: Pressto p

broadcasting a particular program type. Select AUDIO and press ENTER.Select PTY to view the broadcast information or PTY SEARCH to searchfor stations

Maintenance and Specifications 164Engine compartment 166Engine oil 169Battery 173Fuel information 180Part numbers 207Refill capacities 208Lubricant sp

system will return to the current playing media. Select AUDIO and pressENTER. Select TRAF ANNOU and press ENTER. Turn the rotary controlto turn on/off

soft key next to the desired frequency.CD/MP3: Press to select the previous/next track of the current CD/MP3.16. Fade: Press FADE and turn theright co

• A maximum of 20 directories is recommended as additional directorieswill increase the access time.• Each directory can contain a maximum of 254 trac

Don’t:• Expose tapes to direct sunlight, extreme humidity, heat or cold.• Leave tapes in the cassette player for a long time when not beingplayed.CD/C

HEATER ONLY SYSTEM(IF EQUIPPED)1. Air flow selections: Controlsthedirectionoftheairflowinthevehicle. See the following for a briefdescription on each

To aid in side window defogging/demisting in cold weather:1. Select2. Set the temperature control to full heat3. Set the fan speed to HI4. Direct the

5. A/C: Uses outside air to cool the vehicle. Air flows from theinstrument panel vents only.6. Temperature selection: Controls the temperature of the

REAR WINDOW DEFROSTERThe rear defroster control is located on the instrument panel.Press the rear defroster control to clear the rear window of thin i

HEADLAMP CONTROLTurns the lamps off.Turns on the parkinglamps, instrument panel lamps,license plate lamps and tail lamps.Turns the headlamps on.Foglam

High beamsPush the lever toward theinstrument panel to activate. Pullthe lever towards you to deactivate.Flash to passPull toward you slightly to acti

CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth

VOR1. Park the vehicle on a level surface approximately 7.6 meters (25 feet)from the vertical wall or the screen directly in front of it.2. Measure th

5. Remove the headlamp bulb cover by releasing the four snap hooks(two top and two bottom).Note: On the left headlamp, pull the bulb cover approximate

INTERIOR LAMPSDome lampsThe dome lamp is equipped with acontrol switch that will illuminatewhen:• the doors are closed and theswitch is in the on posi

Function Trade numberHeadlamps (VOR) HB2Headlamps (high beam, VOL) H7Headlamps (low beam, VOL) D2SPark lamp (front, VOL) W5WTurn lamp (front, VOL) 345

Replacing headlamp bulbsMake sure the headlamp switch is in the OFF position.To remove the high or low beam headlamp bulb:1. Lift the hood and remove

Replacing grill-mounted front parking lamp/turn signal bulbs1. Make sure the headlamp controlis in the OFF position and open thehood.2. Remove the cov

Replacing tail/brake/backup lights and turn signal bulbs (coupe)1. Make sure the headlamp controlis in the OFF position and thenopen the hatchback.2.

Replacing tail/brake/backup lights and turn signal bulbs (wagon)1. Make sure the headlamp controlis in the OFF position and thenopen the hatchback.2.

Replacing high-mount brake lamp bulbsSedan1. Make sure the headlamp controlis in the OFF position and open theluggage compartment.2. Using a screw dri

Replacing the luggage compartment lamp1. Make sure the headlamp controlis in the OFF position.2. Carefully pry out the lightassembly from the holder w

SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury and prevent possibledamage to others, you

MULTI-FUNCTION LEVERWindshield wiper: Move the leverdown for a single wipe.For intermittent operation, movecontrol up one position and adjustthe rotar

Changing the wiper blades1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Push the lockpin manually to releas

HORNPress the steering wheel pad. Thehorn can be operated when theignition is off.AUXILIARY POWER POINTPower point outlets are designedfor accessory u

Press and hold the bottom part ofthe rocker switch to open thewindow. Press and hold the top partof the rocker switch to close thewindow.One touch dow

Heated mirrors (if equipped)Both mirrors are heatedautomatically to remove ice, mistand fog when the rear windowdefrost is activated.Do not remove ice

3. Press the SET ACCEL controland release it.4. Take your foot off the acceleratorpedal.5. The indicator light on theinstrument cluster will turn on.N

Increasing speed while using speed controlThere are two ways to set a higherspeed:• Press and hold the SET ACCELcontrol until you get to thedesired sp

Turning off speed controlPress the speed control OFFcontrol.Note: When you turn off the speedcontrol or the ignition, your speedcontrol set speed memo

Relearning function: In case the moon roof does not close properlyanymore, follow this relearning procedure.• Tilt the moon roof into the vent positio

and security when appropriately used, particularly in emergencysituations. Safety must be paramount when using mobile communicationsequipment to avoid

for Emissions Defect and Emissions Performance Warranties. For adetailed description of what is covered and what is not covered, refer tothe Warranty

WagonPull out the roller cover and securethe retaining points. The cover canbe removed completely by pressinginward on both ends of the support.To red

KEYSThe key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer.You should always carry a second key w

2. Press the power door unlock control three times.3. Turn the ignition key from ON to OFF.4. Press the power door unlock control three times.5. Turn

To open the luggage compartmentdoor (lid) from within the luggagecompartment, pull the illuminated“T” shaped handle and push up onthe trunk lid. The h

REMOTE ENTRY SYSTEM (IF EQUIPPED)This device complies with part 15 of the FCC rules and with RS-210 ofIndustry Canada. Operation is subject to the fol

Unlocking the doors1. Press and release to unlock the driver’s door. Note: The interiorlamps will illuminate.2. With the all-door remote entry, pressa

To replace the battery:1. Twist a thin coin between the twohalves of the remote entrytransmitter near the key ring. DONOT TAKE THE RUBBER COVERAND CIR

To reprogram the remote entrytransmitters:1. Close all doors and fasten the driver’s seat belt to ensure conflictingchimes do not sound during the pro

key chain may cause vehicle starting issues. You need to prevent theseobjects from touching the coded key while starting the engine. Theseobjects will

1. Insert a previously programmedcoded key into the ignition.2. Turn the ignition from the 3 (OFF) position to the 4 (ON) position.Keep the ignition i

not access event data recorder information without obtaining consent,unless pursuant to court order or where required by law enforcement,other governm

PERIMETER ALARM SYSTEM (IF EQUIPPED)The perimeter anti-theft system will warn you in the event of anunauthorized entry to your vehicle.If there is any

SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a

Adjusting the front manual seatPull the lever located under thefront edge of the seat to move theseat forward or backward.Turn the control to adjust t

Heated seats (if equipped)The heated seats switch is located on the center console.To operate the heated seats:• Push control to activate.• Push again

On three door models, front safetybelts should be pulled backwards toallow easier entry to or exit fromthe rear seats.Do not place objects behind the

Folding the rear seat back forwardCoupe and wagonRemove the head restraints (ifequipped) of the rear seats andstow them on the floor behind thefront s

Folding the seat cushion and seatback forwardPull the loop between the respectiveseat cushion and seatback, and foldthe seat cushion on that sideforwa

How does the personal safety system work?The Personal Safety System can adapt the deployment strategy of yourvehicle’s safety devices according to cra

Front safety belt pretensionersThe safety belt pretensioners are designed to tighten the safety beltsfirmly against the occupant’s body during a colli

Safety belt precautionsAlways drive and ride with your seatback upright and the lapbelt snug and low across the hips.To reduce the risk of injury, mak

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-

Combination lap and shoulder belts1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until

BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED ifthe seat belt assembly “automatic locking retractor” feature orany other seat belt function is not oper

How to use the automatic locking mode• Buckle the combination lap andshoulder belt.• Grasp the shoulder portion andpull downward until the entirebelt

Safety belt pretensionerYour vehicle is equipped with safety belt pretensioners at the driver andfront outboard passenger seating positions.The safety

Position the safety belt height adjusters so that the belt restsacross the middle of your shoulder. Failure to adjust the safetybelt properly could re

If... Then...The driver’s safety belt is notbuckled approximately 5seconds after the safety beltwarning light has turned off...The BeltMinder feature

Reasons given... Consider...“I was in a hurry” Prime time for an accident.BeltMinder reminds us to take a fewseconds to buckle up.“Safety belts don’t

One time disableAny time the safety belt is buckled and then unbuckled during anignition ON cycle, the BeltMinder will be disabled for that ignition c

5. Buckle then unbuckle the safety belt three times, ending with thesafety belt unbuckled.• After step 5 the safety belt warning light will be turned

equipped), child safety seat LATCH and tether anchors, and attachinghardware, should be inspected after a collision. Ford Motor Companyrecommends that

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng

Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body in

Do not attempt to service, repair, or modify the air bagsupplemental restraint systems or its fuses. See your Ford orLincoln Mercury dealer.Children a

The air bags inflate and deflaterapidly upon activation. After air bagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burn

• diagnostic module.• and the electrical wiring which connects the components.The diagnostic module monitors its own internal circuits and thesuppleme

Do not lean your head on the door. The side air bag could injureyou as it deploys from the side of the seatback.Do not attempt to service, repair, or

The fact that the air bags did not inflate in a collision does not mean thatsomething is wrong with the system. Rather, it means the forces werenot of

Do not leave children, unreliable adults, or pets unattended inyour vehicle.Safety belts and seats can become hot in a vehicle that has beenclosed up

Do not leave children, unreliable adults, or pets unattended inyour vehicle.Child booster seatsChildren outgrow a typical convertible or toddler seat

Types of booster seatsThere are two types of belt-positioning booster seats:• Those that are backless.If your backless booster seat has aremovable shi

Follow all instructions provided by the manufacturer of thebooster seat.Never put the shoulder belt under a child’s arm or behind theback because it e