Ford 2011 F-550 v.1 Bedienungsanleitung

Introduction 4Instrument Cluster 14Warning lights and chimes 14Gauges 21Message center 22Entertainment Systems 60AM/FM stereo 60AM/FM stereo with CD 6

Vehicle Modification Data RecordingSome aftermarket products may cause severe engine and/or transmissiondamage; refer to the What is not covered secti

AUXILIARY POWER POINT (12V DC)Power outlets are designed for accessory plugs only. Do not insertany other object in the power outlet for this will dam

Power point (110V AC) (if equipped)The 110V AC power point outlet is used for powering electrical devicesthat require up to 150W. Exceeding the 150W l

The 110V AC power point can provide power whenever the vehicleignition is in the on position and the power point green indicator lightlocated in the t

One-touch downAllows the driver’s window to open fully without holding the controldown. Press the switch completely down to the second detent andrelea

INTERIOR MIRRORThe interior rear view mirror has two pivot points on the support armwhich lets you adjust the mirror up or down and from side to side.

3. Return to the center position to lock mirrors in place.The spotter mirror below the main glass (if equipped) must be adjustedmanually.Heated outsid

Note: When powerfolding the mirrors, it is normal to hear the sound ofthe motors.Powerfold mirror positions, from left to right: Position 1, Position

Telescoping mirrors (if equipped)The telescoping feature allows themirror to extend approximately2.75 inches (70 mm). This feature isespecially useful

Mirror-mounted side turn signal indicator (if equipped)When the vehicle turn signals areactivated, the outer portion of themirror housing will blink a

The accelerator and brake pedal positions are saved when doing amemory set function and can be recalled along with the vehiclepersonality features whe

EXPORT UNIQUE (NON–UNITED STATES/CANADA) VEHICLESPECIFIC INFORMATIONFor your particular global region, your vehicle may be equipped withfeatures and o

Note:• Vehicle speed may vary momentarily when driving up and down asteep hill.• If the vehicle speed increases above the set speed on a downhill, you

STEERING WHEEL CONTROLS (IF EQUIPPED)Audio control featuresMEDIA: Press repeatedly to scrollthrough available audio modes.SEEK : Press to selectthe pr

Press to scroll through various menus and selections. PressOK to confirm your selection.For further information on the SYNC威 system, refer to the SYNC

If your vehicle is equipped with this option, there will also be a relay boxlocated on the driver side end of the instrument panel. See yourauthorized

MOON ROOF (IF EQUIPPED)The moon roof control is located on the overhead console.WARNING: Do not let children play with the moon roof or leavechildren

UNIVERSAL GARAGE DOOR OPENER (IF EQUIPPED)Your vehicle may be equipped with a universal garage door opener whichcan be used to replace the common hand

Types of garage door openers (rolling code and fixed code)The Car2U威 Home Automation System may be programmed to operaterolling code and fixed code ga

1. Firmly press the two outerCar2U威 system buttons for1–2 seconds, then release.2. Go to the garage to locate thegarage door opener motor and its“lear

To program another rolling code device such as an additional garage dooropener, a security device or home lighting, repeat Steps 1 through 4substituti

3. To input these positions into theCar2U威 system, simultaneouslypress all three Car2U威 systembuttons for a few seconds and thenrelease to put the dev

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag

To erase programming on the Car2U威 system (individual buttons cannotbe erased), use the following procedure:1. Firmly press the two outsideCar2U威 syst

TAILGATE LOCK (IF EQUIPPED)Your vehicle may be equipped with atailgate lock designed to helpprevent theft of the tailgate.• Insert ignition key and tu

4. Lower the tailgate.5. Using a screwdriver, gently prythe spring clip (on each connector)past the head of the support screw.Disconnect cable.6. Disc

• Always use grab handle when stepping up and down.• Step not intended for bare-footed use.• Keep step clean from contamination before use (e.g. snow,

2. Open the latches to release thepanels.3. Rotate the panels toward thetailgate.Repeat Steps 1–3 for the other side of the bed extender.4. Connect th

5. Ensure the latch rod is insertedinto the tailgate hole and the lockingpins on both sides are engaged intotheir holes in the pick-up box.6. Reverse

KEYSYour vehicle may be equipped withtwo integrated keyhead transmitters(IKTs). The key blade functions as aprogrammed key which starts thevehicle and

MyKey™ restricted featuresStandard settings – These settings cannot be changed•The audio system will be muted whenever Belt-Minder威 is activateduntil

For optional message center1. At the main menu screen select SETTING then MYKEY by pressingOK or the right arrow key.2. Press OK to select CREATE MYKE

2. Use the up and down arrows to get to any of the optional features.3. Press the right arrow key to bring up the settings available for eachfeature.4

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi

Using MyKey™ with remote start systemsMyKey™ is not compatible with non Ford-approved aftermarket remotestart systems. If you choose to install a remo

Note: For all vehicles with a non Ford-approved remote start installed, itis possible to program all ’real’ keys as MyKeys™, in which case, you willne

TroubleshootingCondition Potential CausesCan’t create a MyKey™ • Key in the ignition is already aMyKey™.• Key in the ignition is the last remainingAdm

Condition Potential CausesI accidentally programmedall keys as MyKeys™• Vehicle has a non Ford-approved remotestart system that is recognized as anAdm

POWER DOOR LOCKS (IF EQUIPPED)Press control to unlock all doors.Press control to lock all doors.Smart locks (if equipped)This feature prevents you fro

The autolock feature repeats when:• any door is opened then closed while the ignition is in the on positionand the vehicle speed is 9 mph (15 km/h) or

Keyless entry keypad autolock enable/disable procedure1. Turn the ignition to the offposition.2. Close all the doors.3. Enter factory–set 5–digit entr

Power door lock switch autounlock enable/disable procedureBefore starting, ensure the ignition is in the off position and all vehicledoors are closed.

CHILDPROOF DOOR LOCKS (IF EQUIPPED)• When these locks are set, therear doors cannot be opened fromthe inside.• The rear doors can be openedfrom the ou

The typical operating range for your IKT is approximately 33 feet(10 meters). A decrease in operating range could be caused by:• weather conditions,•

WARNING LIGHTS AND CHIMESBase instrument cluster with standard measure shown; metricsimilarOptional instrument cluster with standard measure shown; me

Switching from two step to one step door unlockingYour vehicle comes with two step unlocking enabled. Unlocking can beswitched between two step and on

2. Press and hold control button 1for five seconds. A tone will beheard after two seconds confirmingmemory position has been set.Continue to hold unti

3. Insert the new battery. Refer tothe instructions inside the IKT forthe correct orientation of thebattery. Press the battery down toensure that the

The dome lamp control (if equipped) must not be set to the off positionfor the illuminated entry system to operate.The lights will not turn off if:• t

Starting the engine with remote startTo start the engine using remote start:Note: Each button press must be done within 3 seconds of each other. Ifthi

SECURICODE™ KEYLESS ENTRY SYSTEM (IF EQUIPPED)You can use the keyless entrykeypad to lock or unlock the doorswithout using a key.The keypad can be ope

3. Press and hold the 1 • 2 for two seconds. This must be done withinfive seconds of completing Step 2.Your personal code is now erased and only the f

Note: Large metallic objects, electronic devices that are used topurchase gasoline or similar items, or a second coded key on the samekey chain may ca

1. Insert the first previouslyprogrammed coded key into theignition and turn the ignition fromthe 1 (off) position to the 3 (on)position (maintain ign

Arming the systemWhen armed, this system will respond if unauthorized entry isattempted. When unauthorized entry occurs, the system will flash thepark

bulb works. If any light remains on after starting the vehicle, refer to therespective system warning light for additional information.Standard messag

FRONT SEATINGWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the e

To adjust the head restraint, do the following:1. Adjust the seatback to an upright driving/riding position.2. Raise the head restraint bypulling up o

To remove the adjustable head restraint, do the following:1. Pull up the head restraint until itreaches the highest adjustmentposition.2. Simultaneous

Properly adjust the head restraint so that the top of the head restraint iseven with the top of your head and positioned as close as possible to theba

To reinstall the non-adjustable head restraint, do the following:1. Insert the two stems into theguide sleeve collars.2. Push the head restraint downu

• Pull the release lever handlelocated on the side of the seat upto move the seatback forward orbackward.20 percent front seat armrest and console (if

To gain access to the under-seatstorage compartment (if equipped)in your seat cushion, lift the latch toopen the lid. The lid cannot beopened when the

Move the control in the directionsshown to move the seat forward orbackward.Power recline (if equipped)Press the control to recline theseatback forwar

Heated and cooled seats (if equipped)The controls for the climate controlled seats are located on the dualelectronic automatic temperature control (DE

If the engine falls below 350 rpm while the cooled seats are on, thefeature will turn itself off and will need to be reactivated.Climate controlled se

WARNING: Under engine misfire conditions, excessive exhausttemperatures could damage the catalytic converter, the fuelsystem, interior floor coverings

To install a filter:1. Position the filter in it’s housingmaking sure that the far forwardend is all the way up in the housing.2. Push in on the cente

The seat will move to the final position when the key is in the ignition (ifeasy entry feature is enabled).Easy-access/easy-out feature (if equipped)T

4. Cycle the ignition key between the off position and the on position atotal of three times ending with the ignition in the off position.5. Engage th

Removal of the second-row non-adjustable head restraints is the same asthe front row center head restraint. Refer to Front-row centernon-adjustable he

Folding the rear seatback (Crew Cab)1. Pull forward on the control tofold down the seatback.2. Pull down on the handle and liftup on the seatback to r

Rear center armrest (if equipped)To use the armrest simply rotate itforward from the seatback.Rear under seat storage (if equipped) (Crew Cab)The rear

Use your vehicle key to lock thestorage space.SAFETY RESTRAINTSSafety restraints precautionsWARNING: Always drive and ride with your seatback uprighta

WARNING: In a rollover crash, an unbelted person issignificantly more likely to die than a person wearing a safetybelt.WARNING: Each seating position

2. To unfasten, push the releasebutton and remove the tongue fromthe buckle.Restraint of pregnant womenWARNING: Always ride and drive with your seatba

Automatic locking modeWhen to use the automatic locking modeIn this mode, the shoulder belt is automatically pre-locked. The belt willstill retract to

WARNING: Driving a vehicle with the brake system warninglight on is dangerous. A significant decrease in brakingperformance may occur. It will take yo

How to disengage the automatic locking modeDisconnect the combination lap/shoulder belt and allow it to retractcompletely to disengage the automatic l

WARNING: Failure to replace the safety belt assembly underthe above conditions could result in severe personal injuries inthe event of a collision.Saf

Safety belt warning light and indicator chimeThe safety belt warning light illuminates in the instrument cluster and achime sounds to remind the occup

If... Then...The driver’s safety belt isbuckled before the ignitionswitch is turned to the onposition...The Belt-Minder威 feature will notactivate.The

Reasons given... Consider...“The people I’m with don’t wearbelts”Set the example, teen deaths occur 4times more often in vehicles with TWOor MORE peop

WARNING: While the design allows you to deactivate yourBelt-Minder威, this system is designed to improve your chances ofbeing safely belted and survivi

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right

WARNING: Never place your arm over the airbag module as adeploying airbag can result in serious arm fractures or otherinjuries.To properly position yo

WARNING: An infant in a rear-facing seat faces a high risk ofserious or fatal injuries from a deploying passenger airbag. Rearfacing infant seats shou

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt

Door ajar (RTT): Displays whenthe ignition is in the on position andany door is open.Engine coolant temperature(RTT): Illuminates when the enginecoola

• one or more impact and safing sensors,• a readiness light and tone• and the electrical wiring which connects the components.The diagnostic module mo

How does the side airbag system work?The design and development of theside airbag system includedrecommended testing proceduresthat were developed by

to inflate in side-impact collisions, not roll-over, rear-impact, frontal ornear-frontal collisions, unless the collision causes sufficient lateraldec

WARNING: All occupants of the vehicle including the drivershould always wear their safety belts even when an airbag SRSand Safety Canopy威 System is pr

Children 12 years old and under should always be properly restrained inthe second row seats. The Safety Canopy威 will not interfere withchildren restra

Determining if the system is operationalThe SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Ref

Passenger airbag ON/OFF switch (if equipped)WARNING: An airbagON/OFF switch may beinstalled in this vehicle. Beforedriving, always look at the face of

Turning the passenger airbag back onThe passenger airbag remains off until you turn it back on.1. Insert the ignition key and turnthe switch to ON.2.

The vast majority of drivers and passengers are much safer with anairbag than without. To do their job and reduce the risk of lifethreatening injuries

3. Medical condition. A passenger has a medical condition which,according to his or her physician:• causes the passenger airbag to pose a special risk

AdvanceTrac威/Traction control(if equipped): Displays when theAdvanceTrac威/Traction control isactive. If the light remains on, havethe system serviced

3. Medical condition: A passenger has a medical condition that,according to his or her physician:• poses a special risk for the passenger if the airba

WARNING: All children are shaped differently. TheRecommendations for Safety Restraints are based on probablechild height, age and weight thresholds fr

• You are required by law to properly use safety seats for infants andtoddlers in the U.S. and Canada.• Many states and provinces require that small c

WARNING: Air bags can kill or injure a child in a child seat.NEVER place a rear-facing child seat in front of an active airbag. If you must use a forw

WARNING: Never place, or allow a child to place, the shoulderbelt under a child’s arm or behind the back because it reducesthe protection for the uppe

SAFETY SEATS FOR CHILDRENInfant and/or toddler seatsUse a safety seat that is recommended for the size and weight of thechild.When installing a child

• Keep the buckle release button pointing up and away from the safetyseat, with the tongue between the child seat and the release button,to prevent ac

2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro

5. Put the safety belt in theautomatic locking mode. To do so,grasp the shoulder portion of thebelt and pull downward until all ofthe belt is pulled o

9. Attach the tether strap (if thechild seat is equipped). Refer toAttaching child safety seats withtether straps later in this chapter.10. Before pla

Seating and Safety Restraints 150Seating 150Safety restraints 166Airbags 176Child restraints 190Tires, Wheels and Loading 212Tire information 214Tire

Speed control (if equipped): Thespeed control system indicator lightchanges color to indicate what modethe system is in:• On (amber light): Illuminate

WARNING: Airbags can kill or injure a child in a child seat. Ifyou must use a forward-facing child seat in the front seat, moveseat all the way back.W

4. Insert the belt tongue into theproper buckle for that seatingpositions until you hear a snap andfeel it latch. Make sure the tongue issecurely latc

7. Before placing the child in theseat, forcibly move the seat forwardand back to make sure the seat issecurely held in place. To checkthis, grab the

The tether strap anchors in your vehicle are in the following positions(shown from top view):• F-Series Regular Cab• F-Series SuperCab• F-Series Crew

Tether strap attachment1. Route the child safety seat tether strap over the back of the seat.For vehicles with adjustable head restraints, route the t

• Rear seats (Crew Cab)If the tether strap is clipped incorrectly, the child safety seat may not beretained properly in the event of a collision.6. Re

Many tether straps cannot be tightened if the tether strap is hooked tothe loop directly behind the child seat. To provide a tight tether strap:1. Rou

Child booster seatsThe belt-positioning booster (booster seat) is used to improve the fit ofthe vehicle safety belt. Children outgrow a typical child

Booster seats should be used until you can answer YES to ALL of thesequestions when seated without a booster seat:• Can the child sit all the way back

• High back booster seatsIf, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boo

GAUGESBase cluster with automatic transmission shown. Metric similar.1. Engine oil pressure gauge: Indicates engine oil pressure. Theneedle should sta

If the booster seat slides on the vehicle seat, placing a rubberized meshsold as shelf or carpet liner under the booster seat may improve thisconditio

For proper care of soiled safety belts, refer to Interior in the Cleaningchapter.WARNING: Failure to inspect and if necessary replace thesafety belt a

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e

Power is supplied to all four wheels through a transfer case or powertransfer unit. 4WD vehicles allow you to select different drive modes asnecessary

• Narrower — to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUV’s and

TreadwearThe treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernmen

TIRESTires are designed to give many thousands of miles of service, but theymust be maintained in order to get the maximum benefit from them.Glossary

INFLATING YOUR TIRESSafe operation of your vehicle requires that your tires are properlyinflated. Remember that a tire can lose up to half of its air

under-inflation of the tires, improper tires (load range, size, or type), orvehicle modifications such as lift-kits. In the event that your vehicleexp

Note: Some spare tires operate at a higher inflation pressure than theother tires. For T-type/mini-spare tires (see the Dissimilar sparetire/wheel inf

Altering the severity of the driving conditions is recommended to lowerthe transmission temperature into the normal range.Red area The transmission fl

WARNING: Stay out of the trajectory (1) as indicated in theillustration.TIRE CAREInspecting your tires and wheel valve stemsPeriodically inspect the t

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them

U.S. DOT Tire Identification Number (TIN)Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the s

WARNING: When mounting replacement tires and wheels, youshould not exceed the maximum pressure indicated on thesidewall of the tire to set the beads w

• Do not run over curbs or hit the tire against a curb when parkingWARNING: If your vehicle is stuck in snow, mud, sand, etc., donot rapidly spin the

Tire rotationRotating your tires at the recommended interval (as indicated in theScheduled Maintenance Guide chapter) will help your tires wear moreev

WARNING: If the tire label shows different tire pressures forthe front and rear tires and the vehicle is equipped with TPMS(tire pressure monitoring s

INFORMATION CONTAINED ON THE TIRE SIDEWALLBoth U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the

7. H: Indicates the tire’s speed rating. The speed rating denotes thespeed at which a tire is designed to be driven for extended periods oftime under

10. Tire Ply Composition and Material Used: Indicates the number ofplies or the number of layers of rubber-coated fabric in the tire tread andsidewall

Selectable featuresInfo (information menu)Press the INFO button repeatedly tocycle through the following features:TRIP A/BRegisters the distance of in

Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;

Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8

TIRE PRESSURE MONITORING SYSTEM (TPMS) (IF EQUIPPED)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe

following two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including inter

When you believe your system is not operating properlyThe main function of the tire pressure monitoring system is to warn youwhen your tires need air.

Low tire pressurewarning lightPossible cause Customer action requiredFlashing warninglightSpare tire in use Your temporary spare tire is inuse. Repair

TPMS reset procedureThe TPMS reset procedure needs to be performed after each tirerotation on vehicles that require different recommended tirepressure

3. Cycle the ignition to the onposition with the engine off.4. Turn the hazard flashers on thenoff three times. This must beaccomplished within 10 sec

8. Remove the valve cap from the valve stem on the right rear tire.Decrease the air pressure until the horn sounds.9. Remove the valve cap from the va

Follow these guidelines when using snow tires and chains:• Use only SAE Class S chains.• Install chains securely, verifying that the chains do not tou

XX.X AVG MPG (L/100km)Average fuel economy displays your average fuel economy in miles/gallonor liters/100 km.If you calculate your average fuel econo

Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab

Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load

GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S

• Example only:WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or

GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)

WARNING: Do not use replacement tires with lower loadcarrying capacities than the original tires because they maylower the vehicle’s GVWR and GAWR lim

• A final example for your vehicle with 1,400 lb. (635 kg) of cargo andluggage capacity. You and one of your friends decide to pick upcement from the

TRAILER TOWINGNote: The trailer towing chart in this section applies to vehiclesequipped with a gasoline engine; for vehicles equipped with a dieselen

WARNING: Towing trailers beyond the maximum recommendedtrailer weight which exceeds the limit of the vehicle’s GCWR,GVWR, GAWR or tire ratings could r

•To determine which trailer hitch your vehicle is equipped with, refer tothe trailer hitch label located on trailer hitch cross tube. Once youdetermin

System check and vehicle feature customizationPress the SETUP button repeatedlyto cycle the message center throughthe following features:Note: When re

Fifth-wheel trailer hitch (if equipped)To find the maximum trailer weight allowed for your vehicle, consultyour authorized dealer (or the RV and Trail

Trailer brakesElectric brakes and manual, automatic or surge-type trailer brakes aresafe if installed properly and adjusted to the manufacturer’sspeci

The TBC user interface consists ofthe following:1. +/- (GAIN adjustmentbuttons): Pressing these buttonswill adjust the TBC’s power outputto the traile

2. Manual control lever: Slide the control lever to the left to activatepower to the trailer’s electric brakes independent of the tow vehicle’sbrakes

6. If the trailer wheels lock-up (indicated by squealing tires), reduce theGAIN setting; if the trailer wheels turn freely, increase the GAIN setting.

• The TBC interacts with the brake system of the vehicle, includingABS, in order to reduce the likelihood of trailer wheel lockup.Therefore, if these

Servicing after towingIf you tow a trailer for long distances, your vehicle will require morefrequent service intervals. Refer to Special operating co

Braking• Anticipate the need to stop; allow much more distance and time tostop than normal.• Do not apply the trailer brakes for extended periods of t

RECREATIONAL TOWINGFollow these guidelines if you have a need for recreational (RV) towing.An example of recreational towing would be towing your vehi

STARTINGPositions of the ignition1. Off— shuts off the engine and allaccessories/locks the steering wheeland allows key removal.2. Accessory— allows t

To reset the oil monitoring system to 100% after each oil change,perform the following:1. Press and release the SETUP button to display “OIL LIFE XXX%

WARNING: Do not start your vehicle in a closed garage or inother enclosed areas. Exhaust fumes can be toxic. Always openthe garage door before you sta

3. Turn the key to 3 (on) withoutturning the key to 4 (start).Some warning lights will briefly illuminate. See Warning lights andchimes in the Instrum

Cold weather starting (flexible fuel vehicles only)The starting characteristics of all grades of E85ethanol make itunsuitable for use when ambient tem

Important ventilating informationIf the engine is idling while the vehicle is stopped for a long period oftime, open the windows at least 1 inch (2.5

• Make certain that the extension cord is in excellent condition (notpatched or spliced). Store your extension cord indoors attemperatures above 32°F

BRAKESOccasional brake noise is normal. If a metal-to-metal, continuous grindingor continuous squeal sound is present, the brake linings may be worn-o

ABS warning lampThe ABS lamp in the instrumentcluster momentarily illuminateswhen the ignition is turned on. Ifthe light does not illuminate duringsta

Pull the release lever to release theparking brake. To prevent the pedalfrom releasing too quickly, placeyour left foot on the service brakepedal, the

WARNING: Aggressive driving in any road conditions can causeyou to lose control of your vehicle increasing the risk of severepersonal injury or proper

WARNING: Vehicle modifications involving braking system,aftermarket roof racks, suspension, steering system, tireconstruction and/or wheel/tire size m

ZONE <XX> RESET = CHANGEThe compass heading is displayed as one of N, NE, E, SE, S, SW, W andNW in the message center display.Refer to Compass z

The AdvanceTrac威 with RSC威system includes a stability controlbutton located on the instrumentpanel to the right of the climatecontrol system, a stabil

During TCS events the stability control light in the instrument clusterwill flash.If the TCS is activated excessively in a short period of time, the b

Roll Stability Control™ (RSC威)Roll Stability Control™ (RSC威) may help to maintain roll stability of thevehicle during adverse maneuvers. RSC威 operates

AdvanceTrac威 with RSC威 FeaturesButton functionsStabilitycontrollightRSC威 ESC TCSDefault at start-upIlluminatedduring bulbcheckEnabled Enabled EnabledB

Trailer sway controlYour vehicle may be equipped with trailer sway control. When properlyequipped, trailer sway control will use the vehicle’s Advance

HILL DESCENT CONTROL (IF EQUIPPED)Hill descent control allows the driver to set and maintain vehicle speedwhile descending steep grades in various sur

Note: Noise from the ABS pump motor may be observed during hilldescent control operation. This is a normal characteristic of the ABS andshould be no r

• loose or worn steering components• improper steering alignmentIf any steering components are serviced or replaced, install newfasteners (many are co

For 2WD vehicles and vehiclesequipped with a manual shift4WD system:Turn the control to ON. Theindicator light will display in theinstrument cluster.O

WARNING: Vehicles with a higher center of gravity such as utilityvehicles and trucks handle differently than vehicles with a lowercenter of gravity. U

Perform compass calibration in an open area free from steel structuresand high voltage lines. For optimum calibration, turn off all electricalaccessor

5. Remove the top half of the shroud.6. Remove the three fasteners underthe column that secure the lowershroud half to the column.7. Pull the lock lev

AUTOMATIC TRANSMISSION OPERATIONUnderstanding the shift positions of the 5–speed automatictransmission (if equipped)This vehicle is equipped with an a

N (Neutral)With the gearshift lever in N (Neutral), the vehicle can be started and isfree to roll. Hold the brake pedal down while in this position.D

3 (Third)Transmission starts and operates in third gear only.Used for improved traction on slippery roads. Selecting 3 (Third)provides engine braking.

P (Park)This position locks the transmission and prevents the rear wheels fromturning.To put your vehicle in gear:1. Start the engine2. Press the brak

The TOW HAUL indicator light willilluminate in the instrument cluster.Tow/haul delays upshifts to reduce frequency of transmission shifting.Tow/haul a

1 (First)• Provides maximum engine braking.• Allows upshifts by moving gearshift lever.• The transmission will not downshift into 1 (First) at high sp

By moving the gearshift lever from the D (Drive) position to the M(Manual) position you may now manually select the gear you desire.Only the current g

WARNING: The hill assist feature does not replace the parkingbrake. When you leave the vehicle, always apply the parkingbrake and select first or reve

REVERSE SENSING SYSTEM (IF EQUIPPED)The reverse sensing system (RSS) sounds a tone to warn the driver ofobstacles near the rear bumper when the R (Rev

LANGUAGE = ENGLISH / SPANISH / FRENCHAllows you to choose which language the message center will display in.Selectable languages are English, Spanish,

The RSS detects obstacles up to6 feet (2 meters) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to the fi

REARVIEW CAMERA SYSTEM (IF EQUIPPED)The rearview camera system,located on the tailgate, provides avideo image, which appears in therearview mirror or

Image delay if displayed through the rearview mirror:When shifting out of R (Reverse) and into any other gear, the image inthe rearview mirror will re

Night time and dark area useAt night time or in dark areas, the camera system relies on the reverselamp lighting to produce an image. Therefore it is

turn the hub locks completely clockwise; to disengage the hubs(FREE), turn the hub locks completely counterclockwise.• The vehicle should not be drive

4WD system indicator lightsThe indicator lights illuminate in the message center in thereconfigurable telltale (RTT) under the following conditions. R

Shifting from 2H (2WD) to 4H (4x4 High)Engage the locking hubs by rotatingthe hub lock control from FREE toLOCK, then move the transfer caselever from

3. Move the transfer case shift leverthrough N (Neutral) directly to 4L(4x4 Low).4. If the shift lever does not, or onlypartially moves to the 4L (4x4

WARNING: Do not leave the vehicle unattended with thetransfer case in the N (Neutral) position. Always set the parkingbrake fully and turn off the ign

Shifting to/from 4L (4X4 low)1. Bring the vehicle to a speed of 3 mph (5 km/h) or less.2. Place the transmission in N (Neutral).3. Move the 4WD contro

Cleaning 352Maintenance and Specifications 361Engine compartment 362Engine oil 366Battery 368Engine coolant 370Fuel information 377Air filter(s) 395Pa

PASSENGER DOOR AJAR — Displayed when the passenger’s door isnot completely closed.REAR LEFT DOOR AJAR — Displayed when the rear left door is notcomple

Drive cautiously to avoid vehicle damage from concealed objects such asrocks and stumps.You should either know the terrain or examine maps of the area

If your vehicle gets stuckIf your vehicle gets stuck in mud or snow it may be rocked out byshifting between forward and reverse gears, stopping betwee

• If the vehicle goes from one type of surface to another (i.e., fromconcrete to gravel) there will be a change in the way the vehicleresponds to a ma

SandWhen driving over sand, try to keep all four wheels on the most solidarea of the trail. Avoid reducing the tire pressures but shift to a lowergear

“Tread Lightly” is an educationalprogram designed to increase publicawareness of land-use regulationsand responsibilities in our nationswilderness are

Descend a hill in the same gear youwould use to climb up the hill toavoid excessive brake applicationand brake overheating. Do notdescend in neutral;

WARNING: If you are driving in slippery conditions that requiretire cables, then it is critical that you drive cautiously. Keepspeeds down, allow for

Ford Super Duty Vehicles are qualified for use as a stationary or mobilepower source, within limits detailed in the Ford Truck Body BuildersLayout Boo

• The Total Accessory Reserve Capacity (TARC) is shown on the lowerright side of the vehicle’s Safety Compliance Certification Label. Thisapplies to F

Snowplowing with your airbag-equipped vehicleYour vehicle is equipped with a driver and passenger airbagSupplemental Restraint System (SRS) The SRS is

TRAIN RIGHT FRONT TIRE (if equipped) — Displayed whentraining the TPMS. Refer to TPMS reset procedure in the Tires, Wheelsand Loading chapter for more

Do not rock the vehicle if the engine is not at normal operatingtemperature. Do not rock the vehicle for more than a minute. Thetransmission and tires

ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside

Canadian customers refer to your Warranty Guide or visit ourwebsite at www.ford.ca for information on:Using roadside assistanceComplete the roadside a

FUEL PUMP SHUT-OFFIn the event of a moderate to severe collision, this vehicle is equippedwith a fuel pump shut-off feature that stops the flow of fue

Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V

To remove the fuse panel cover, pullthe panel toward you. When theclips of the panel disengage, let thepanel fall easily.To remove a fuse use the fuse

The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingProtected Circuits1 30A Not used (spare)2 15A Upfitter relay #43 30A Not used (spare)4

Fuse/RelayLocationFuse AmpRatingProtected Circuits11 10A Instrument cluster12 15A Interior lighting, Lighted runningboard lamps13 15A Right turn signa

Fuse/RelayLocationFuse AmpRatingProtected Circuits30 15A Parking lamp relay, TT parkinglamp relay31 5A Trailer brake controller (brakesignal), Custome

Power distribution boxThe power distribution box is located in the engine compartment. Thepower distribution box contains high-current fuses that prot

VEHICLE NEAR TOP SPEED — Displayed when a MyKey™ is in useand the MyKey speed limit is on and the vehicle speed is approaching80 mph (130 km/h). Refer

Fuse/RelayLocationFuse AmpRatingProtected Circuits9 30A* Driver seat10 — Not used11 — Not used12 — Not used13 — Not used14 — Not used15 Diode Fuel pum

Fuse/RelayLocationFuse AmpRatingProtected Circuits38 Relay Powertrain control module(PCM) (diesel engine),Electronic control module (ECM)(gas engine)3

Fuse/RelayLocationFuse AmpRatingProtected Circuits63 — Not used64 — Not used65 — Not used66 20A** Fuel pump67 — Not used68 10A** Fuel pump relay coil6

Fuse/RelayLocationFuse AmpRatingProtected Circuits93 20A* Auxiliary power point #394 25A* Upfitter #195 25A* Upfitter #296 50A* ABS pump97 40A* Invert

WARNING: Refer to Tire pressure monitoring system (TPMS)in the Tires, Wheels and Loading chapter for importantinformation. If the tire pressure monito

• Ground clearance and parking at curbs• Winter weather driving capability• Wet weather driving capabilityIt is not recommended that the vehicle be op

Spare tire informationNote: If your vehicle is equipped the tire pressure monitoring system(TPMS), the system indicator light will illuminate when the

Location of the spare tire and toolsIf your vehicle is equipped with a spare tire, jack and associated tools,refer to the following table for their lo

• Vehicles equipped with dualrear wheels, insert the lugwrench extension into the lugwrench to reach the lug nuts.2. Attach the spare tire lock key (A

If equipped with a tether, perform the following additional steps:6. Lift the spare tire on end toaccess the tether attachment.7. Use the lug wrench t

TBC GAIN = XX.X NO TRAILER (if equipped) — Displays thecurrent gain setting for the trailer brake when a trailer is not connected.Refer to Trailer tow

1. Turn engine off and block thewheel that is diagonally opposite ofthe flat tire using the wheel chock,if equipped. If the vehicle is a4x4, lock the

• Front driver side (4x4)Note: Make sure the jack fits ontothe flat area on the outboard side ofthe differential.• Front passenger side (4x4)Note: Vie

Never use the front or reardifferential as a jacking point.WARNING: To lessen therisk of personal injury, donot put any part of your bodyunder the veh

12. Position the jack according to the following guides:• Front (4x2): F–350 DRWNote: Place jack directly underI-beam.• Front driver side (4x4): F–350

• Front: F–450/F–550• Rear: F-350 DRW• Rear: F-450/F-55013. Insert the jack handle into thepump linkage.14. Use an up-and-down motionwith the jack han

16. Replace the flat tire with the spare tire, making sure the valve stemis facing outward on all front an inboard rear wheels. If replacing theoutboa

19. Stow the flat tire. Refer to Stowing the flat/spare tire if the vehicleis equipped with a spare tire carrier.20. Stow the jack, jack handle and lu

2. Hold the ornament so that all ofthe retention clips are sitting on theflange of the lug nuts.3. Use your hand or rubber mallet totap the ornament i

Stowing the flat/spare tireNote: Failure to follow spare tire stowage instructions may result infailure of cable or loss of spare tire.If you are stow

WHEEL LUG NUT TORQUE SPECIFICATIONSOn vehicles equipped with single rear wheels, retighten the lug nuts tothe specified torque at 500 miles (800 km) a

TO EXIT 4X4 LOW APPLY BRAKE (if equipped) — Displayed when2WD is selected from 4X4 LOW mode. For more information, refer toFour-wheel drive (4WD) oper

Inspect the wheel pilot hole prior toinstallation. If there is visiblecorrosion in wheel pilot hole,remove loose particles by wipingwith clean rag and

4. Check all battery terminals and remove any excessive corrosion beforeyou attach the battery cables. Ensure that vent caps are tight and level.5. Tu

Jump starting1. Start the engine of the booster vehicle and run the engine atmoderately increased speed.2. Start the engine of the disabled vehicle.3.

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

Note: Towing an ESOF 4x4 vehicle with the front wheels on the groundwithout disengaging the front hubs may cause damage to the automatictransmission.N

GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized

In Canada:Mailing address (Ford vehicles)Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4Teleph

In the United States, a warranty dispute must be submitted to the BBBAUTO LINE before taking action under the Magnuson-Moss WarrantyAct, or to the ext

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY)Your satisfaction is important to Ford Motor Company and to your dealer.If a warranty con

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to fee

ENGINE TURNS OFF IN XX (Diesel engine only) — Displayedwhen the vehicle is in the final 30 seconds of a countdown to where theengine will intentionall

If your vehicle must be serviced while you are traveling or living inAsia-Pacific Region, Sub-Saharan Africa, U.S. Virgin Islands, CentralAmerica, the

ORDERING ADDITIONAL OWNER’S LITERATURETo order the publications in this portfolio, contact Helm, Incorporated at:HELM, INCORPORATEDP.O. Box 07150Detro

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft威 Detail Wash (ZC-3-A), which i

WAXING• Wash the vehicle first.• Use a quality wax that does not contain abrasives.• Do not allow paint sealant to come in contact with any non-body(l

ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:•Take care when u

• 6.8L V10 gasoline enginePLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your

helps to remove the hot wax deposited on the wiper blade andwindshield from automated car wash facilities. Be sure to replacewiper blades when they ap

INSTRUMENT PANEL AND CONSOLE (HARLEY-DAVIDSON ONLY)Your vehicle’s instrument panel and console are uniquely painted withboth high and low gloss paints

• If a ring forms on the fabric after spot cleaning, clean the entire areaimmediately (but do not oversaturate) or the ring will set.• Do not use hous

For routine cleaning, wipe the surface with a soft, damp cloth. For morethorough cleaning, wipe the surface with a mild soap and water solution.• Clea

WARNING: When the CLEANING EXHAUST FILTER messageappears in the message center, do not park near flammablematerials, vapors or structures until filter

FORD, LINCOLN AND MERCURY CAR CARE PRODUCTSYour authorized dealer has many quality products available to clean yourvehicle and protect its finishes. T

SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your

OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel.2. Go to the front of th

6.2L V8 gasoline engine1. Windshield washer fluid reservoir2. Engine oil dipstick3. Automatic transmission fluid dipstick4. Brake fluid reservoir5. En

6.8L V10 gasoline engine1. Windshield washer fluid reservoir2. Battery3. Automatic transmission fluid dipstick4. Engine oil filler cap5. Engine oil di

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

To prolong the life of the wiper blades, it is highly recommended toscrape off the ice on the windshield before turning on the wipers. Thelayer of ice

Adding engine oil1. Check the engine oil. For instructions, refer to Checking the engineoil in this chapter.2. If the engine oil level is not within t

Do not use supplemental engine oil additives, cleaners or other enginetreatments. They are unnecessary and could lead to engine damage thatis not cove

Note: Electrical or electronic accessories or components added tothe vehicle by the dealer or the owner may adversely affectbattery performance and du

SPEED LIMITED YYKMH IN XXXKM EXHAUST FLUID EMPTY(Diesel engine only) — Displayed when the diesel exhaust fluid isnearing empty. The vehicle’s top spee

6. Release the parking brake. With your foot on the brake pedal and withthe A/C on, put the vehicle in D (Drive) and allow the engine to idle forat le

• Protection against rust and other forms of corrosion.• Proper function of calibrated gauges.When the engine is cold, check thelevel of the engine co

WARNING: Do not put engine coolant in the windshield washerfluid container. If sprayed on the windshield, engine coolantcould make it difficult to see

Add the proper mixture of coolant and water to the cooling system byfollowing these steps:1. Before you begin, turn the engine off and let it cool.2.

Coolant refill capacityTo find out how much fluid your vehicle’s cooling system can hold, referto Maintenance product specifications and capacities in

How fail-safe cooling worksIf the engine begins to overheat:• The engine coolant temperature gauge will move to the red (hot)area.• The message center

Engine fluid temperature management (except 6.8L V10)Your vehicle has been designed to pull a trailer, but because of the addedload, the vehicle’s eng

WARNING: Never remove the coolant reservoir cap while theengine is running or hot.4. If the coolant level is normal, you may restart your engine andco

Observe the following guidelines when handling automotive fuel:• Extinguish all smoking materialsand any open flames beforefueling your vehicle.• Alwa

Pure ethanol is the alcohol which is the intoxicating agent in liquor, beerand wine. It is distilled from the fermentation of plants such as field cor

SPEED LIMITED YYMPH IN XX MI CONTAMINATED EXHAUSTFLUID (Diesel engine only) — Displayed when the diesel exhaustfluid becomes contaminated. Speed will

RefuelingWARNING: Fuel vapor burns violently and a fuel fire can causesevere injuries. To help avoid injuries to you and others:• Read and follow all

WARNING: The fuel system may be under pressure. If the fuelfiller cap is venting vapor or if you hear a hissing sound, waituntil it stops before compl

Octane recommendationsYour vehicle is designed to use “Regular” unleaded gasoline with a pump(R+M)/2 octane rating of 87. Some stations offer fuels po

Do not add aftermarket fuel additive products to your fuel tank. Itshould not be necessary to add any aftermarket products to your fueltank if you con

ESSENTIALS OF GOOD FUEL ECONOMYMeasuring techniquesYour best source of information about actual fuel economy is you, thedriver. You must gather inform

Calculating fuel economy1. Fill the fuel tank completely and record the initial odometer reading(in miles or kilometers).2. Each time you fill the tan

• Warming up a vehicle on cold mornings is not required and mayreduce fuel economy.• Resting your foot on the brake pedal while driving may reduce fue

EMISSION CONTROL SYSTEMYour vehicle is equipped with various emission control components and acatalytic converter which will enable your vehicle to co

Do not make any unauthorized changes to your vehicle or engine. Bylaw, vehicle owners and anyone who manufactures, repairs, services,sells, leases, tr

Readiness for Inspection/Maintenance (I/M) testingSome state/provincial and local governments may haveInspection/Maintenance (I/M) programs to inspect

ENGINE IDLED SEE MANUAL CONTAMINATED EXHAUSTFLUID (Diesel engine only) — Displayed when the diesel exhaustfluid is contaminated. The vehicle will ente

POWER STEERING FLUIDCheck the power steering fluid. Refer to scheduled maintenanceinformation. If adding fluid is necessary, use only MERCON威 ATF.• Ga

BRAKE FLUID• Vacuum boost system• Hydroboost systemThe fluid level will drop slowly as the brakes wear, and will rise when thebrake components are rep

2. Park the vehicle on a level surface and engage the parking brake.3. With the parking brake engaged and your foot on the brake pedal,start the engin

The transmission fluid should be inthis range if at ambient temperature(50°F-95°F [10°C-35°C]).High fluid levelFluid levels above the safe rangemay re

TRANSFER CASE FLUID (IF EQUIPPED)1. Clean the filler plug.2. Remove the filler plug andinspect the fluid level.3. Add only enough fluid throughthe fil

The following procedure is for vehicles equipped with a gasoline engine.If your vehicle is equipped with a diesel engine, refer to the dieselsupplemen

5. Release the three clamps thatsecure the cover to the air filterhousing. Push the air filter covertoward the center of the vehicle andup slightly to

10. Reconnect the mass air flowsensor electrical connector to theoutlet tube. Make sure the lockingtab on the connector is in the“locked” position (co

• Cover interior trim to prevent fading.• Keep all rubber parts free from oil and solvents.Engine• The engine oil and filter should be changed prior t

Miscellaneous• Make sure all linkages, cables, levers and pins under vehicle arecovered with grease to prevent rust.• Move vehicles at least 25 feet (

CONGRATULATIONSCongratulations on acquiring your new Ford. Please take the time to getwell acquainted with your vehicle by reading this handbook. The

OPTIONAL MESSAGE CENTER (IF EQUIPPED)Your vehicle’s message center is capable of monitoring many vehiclesystems and will alert you to potential vehicl

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem Capacity Ford part nameFord part number /Ford specificationFront axle 5.8 pints (2.8L)Motorcraft

Item Capacity Ford part nameFord part number /Ford specificationEngine coolant(6.2L V8 engine)221.3 quarts(20.2L)Motorcraft威 SpecialtyOrange Engine Co

Item Capacity Ford part nameFord part number /Ford specificationHinges, latches, strikerplates, fuel filler doorhinge and seat tracks— Multi-Purpose G

Item Capacity Ford part nameFord part number /Ford specificationWindshield washer fluid Fill as requiredMotorcraft威 PremiumWindshield WasherConcentrat

ENGINE DATAEngine 6.2L V8 engine 6.8L V10 engineCubic inches 378 413Required fuel 87 octane 87 octaneFiring order 1-3-7-2-6-5-4-8 1-6-5-10-2-7-3-8-4-9

6.8L V10 engine - without A/CIDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulation

Vehicle identification number (VIN)The vehicle identification number islocated on the driver sideinstrument panel.Please note that in the graphic,XXXX

TRANSMISSION CODE DESIGNATIONSYou can find a transmission code onthe Safety Compliance CertificationLabel. The following table tells youwhich transmis

FORD CUSTOM ACCESSORIES FOR YOUR VEHICLEA wide selection of Ford Custom Accessories are available for yourvehicle through your local Ford or Ford of C

Lifestyle•Ash cup / smoker’s package •Racks and carriers*•Bedliners and bedmats •Truck bed camping tent*•Subwoofer* •Sportliner cargo liner*•Towing mi

Main menuFrom the main menu screen you can choose the following:• Gauge Mode• Trip A/B• Fuel Economy• Truck Apps (if equipped)• Settings• InformationS

• Mobile communications systems may harm the operation of yourvehicle, particularly if they are not properly designed for automotiveuse.• To avoid int

FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY)More than 30 million Ford, Lincoln, and Mercury owners have discoveredthe powerful protection of Ford ESP.

Ford ESP Can Quickly Pay for ItselfOne service bill – the cost of parts and labor – can easily exceed theprice of your Ford ESP Service Contract. With

Ford Extended Service Plan4132011 F-250/350/450/550 (f23)Owners Guide, 1st PrintingUSA (fus)

FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY)You can get more protection for your vehicle by purchasing a FordExtended Service Plan (ESP). Ford ESP is

GENERAL MAINTENANCE INFORMATIONWhy maintain your vehicle?This guide describes the scheduled maintenance required for your vehicle.Carefully following

Non-Ford approved chemicals or additives are not required for factoryrecommended maintenance. In fact, Ford Motor Company recommendsagainst the use of

Value shopping for your vehicle’s maintenance needsYour dealership recognizes the competitive landscape of maintenance andlight repair automotive serv

Multi-point inspectionFord recommended scheduled maintenance – In order to keep yourvehicle running right, it is important to have the systems on your

NORMAL SCHEDULED MAINTENANCE AND LOGThe following section contains the “Normal Schedule”. This schedule ispresented at specific mileage (kilometer) in

Press the right arrow key to reach Trip B. Press the left arrow to go backto Trip A.Press OK to pause the Trip A or B screen/press again to un-pause.P

Miles (x 1,000) 7.5 15 22.5 30 37.5 45 52.5 60 67.5 75Kilometers (x 1,000) 12 24 36 48 60 72 84 96 108 120Months 6 12 18 24 30 36 42 48 54 60Change en

Miles (x 1,000) 82.5 90 97.5 105 112.5 120 127.5 135 142.5 150Kilometers (x 1,000) 132 144 156 168 180 192 204 216 228 240Months 66 72 78 84 90 96 102

Every 15,000 miles(24,000 km)Replace cabin air filter (if equipped)Every 30,000 miles(48,000 km)Replace climate-controlled seat filter (ifequipped)Rep

Maintenance schedule logDEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATIO

DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOUR

DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOUR

SPECIAL OPERATING CONDITIONSIf you operate your Ford/Lincoln/Mercury vehicle primarily in one of themore demanding Special Operating Conditions listed

Extensive idling and/or low-speed driving for long distances as in heavycommercial use such as delivery, taxi, patrol car or liveryInspect frequently,

Operating in dusty conditions such as unpaved or dusty roadsInspect frequently, service asrequired– Replace cabin air filter (if equipped).– Replace e

Off-road operationInspect frequently, service asrequired– Replace cabin air filter (if equipped).– Replace engine air filter.– Inspect and lubricate s

• 10 Minutes.• 30 Minutes.• Last 5 Resets.Use the up/down arrows keys to highlight one of the choices; press andhold OK to set your choice.The graph i

Special operating condition logDEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VA

DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOUR

EXCEPTIONSIn addition, there are several exceptions to the Normal Schedule. Theyare listed below:Normal Vehicle Axle Maintenance❑Rear axles and power

COOLANT CHANGE RECORDHot Climate Oil Change Intervals❑If operating conditions are normal and you drive your Ford, Lincoln or Mercury vehicle under typ

Engine coolant change logDEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATI

AAccessory delay ...103AdvanceTrac ...268Air cleaner filter ...394–395, 399Air conditioning ...

in rear seat ...195, 202LATCH ...202Child safety seats - boosterseats ...

refill capacities ...400service points ...362–364Engine block heater ...263Engine oil ...

IIgnition ...259, 404Illuminated visor mirror ...98Infant seats(see Safety seats) ...195Inspec

OOctane rating ...382Oil (see Engine oil) ...366PParental MyKeyprogramming ...126Par

When “Press OK for options” is displayed, pressing OK will open thetrailer options menus:TrailerChange ActiveTrailerWhen this is highlighted, press th

SecuriCode keyless entrysystem ...145SecuriLock passive anti-theftsystem ...146–147S

VVehicle Identification Number(VIN) ...406Vehicle loading ...239Ventilating your vehicle

TrailerRename Trailer Press the right arrow button when this is highlightedto display saved or default trailers. Use the up/downbuttons to highlight a

Determine which magnetic zone youare in for your geographic locationby referring to the zone map.Vehicle (cont’d)Compass(cont’d)Calibration (When choo

MyKeyCreate MyKey Press and hold OK to create MyKeyAdvanceTrac Always on or SelectableMAX MPH(km/h)80 MPH (120 km/h) or OffSpeed Warning 45, 55 or 65

System CheckBrakesTire PressureTrailer BrakeCtrl.Gain and Output (when trailer is connected)No trailer (when no trailer is connected)Trailer SwayPark

• Some messages can be acknowledged and reset by pressing RESET.This allows you to use the full message center functionality by clearingthe message.DO

SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ

POWER REDUCED TO LOWER ENGINE TEMP — Displayed whenthe engine temperature gauge needle moves to H. You may noticereduced engine power. Refer to Engine

STOP SAFELY NOW, the chime will sound, and engine power will bereduced again and shut down below 3 mph (5 km/h). Refer to yourdiesel supplement for mo

can be properly circulated to avoid engine damage from lack oflubrication. A timer will begin a countdown from 30 seconds. Once thecounter has reached

IN XX MILES, SPEED LIMITED TO YY MPH CONTAMINATEDEXHAUST FLUID (diesel engine only) — Displayed when the dieselexhaust fluid becomes contaminated. Spe

SPEED LIMITED TO XX MPH UPON RESTART CONTAMINATEDEXHAUST FLUID (diesel engine only) — Displayed when the dieselexhaust fluid is contaminated. Speed wi

WATER IN FUEL DRAIN FILTER SEE MANUAL (if equipped) —Displayed when the water separator has reached a predeterminedcapacity and needs to be drained. R

TRAIN SPARE TIRE (if equipped) — Displayed when training theTPMS. Refer to TPMS reset procedure in the Tires, Wheels andLoading chapter for more infor

TO EXIT 4X4 LOW SHIFT TO N (if equipped) — Displayed when2WD is selected while the vehicle has been stopped in 4X4 LOW. Formore information, refer to

CHECK LOCKING DIFFERENTIAL (if equipped) — Displayedwhen an electronic locking differential (ELD) system fault is present. Formore information, refer

REAR PARK AID OFF (if equipped) — Displayed when the rear parkaid is disabled by the driver.REAR PARK AID ON (if equipped) — Displayed when the rear p

BREAKING-IN YOUR VEHICLEYour vehicle does not need an extensive break-in. Try not to drivecontinuously at the same speed for the first 1,000 miles (1,

AUDIO SYSTEMSAM/FM stereo system (if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strong

2. AUDIO: Press AUDIO repeatedlyto gain access to the followingsettings:TREB (Treble): Press AUDIO toreach the treble setting. Use/ / SEEK .BASS (Bass

AM/FM stereo single CD/satellite-compatible sound system(if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident

2. (Phone): If your vehicle isequipped with SYNC威, press toaccess SYNC PHONE features. Forfurther information, please refer to your SYNC威 supplement.I

• DELETE SONG: Press OK to delete a song title from the system’smemory. Press / to cycle through the saved songs. When thesong title appears in the di

L..R(Balance): Press MENU to reach the balance setting.Use/ / SEEK, SEEK to adjust the audio between the left(L) and right (R) speakers.B..F(Fade): Pr

4. AUX: Press repeatedly to cyclethrough LINE IN (auxiliary audiomode, if equipped) and SAT1, SAT2and SAT3 modes (satellite radio, if equipped).For lo

current track is finished playing. CD SHUF will appear in the display. Todisengage, press SHUFFLE again. SHUFFLE OFF will appear in thedisplay.Note: I

In satellite radio mode (if equipped), press and release to enterTEXT MODE and display the current song title. While in TEXT MODE,press again to scrol

Auxiliary input jack (if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly recommend

Notice to owners of pickup trucks and utility type vehiclesWARNING: Utility vehicles have a significantly higher rolloverrate than other types of vehi

4. Turn the radio on, using either a tuned FM station or a CD loaded intothe system. Adjust the volume to a comfortable listening level.5. Turn the po

USB port (if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly recommends thatdriver

CD/CD player careDo:• Handle discs by their edges only.(Never touch the playingsurface).• Inspect discs before playing.• Clean only with an approved C

CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommen

Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou

• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w

Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio for theselected channel.No action required.This m

Radio Display Condition Action RequiredNO TEXT Category informationnot available.Category informationnot available at thistime on this channel.The sys

SINGLE ZONE CLIMATE CONTROL1.Defrost: Distributes outside air through the windshield defrostervents and de-mister vents. Can be used to clear the wind

5. Recirculated air (if equipped): Press to activate/deactivate airrecirculation in the vehicle. Recirculated air may reduce the amount oftime needed

DATA RECORDINGService Data RecordingService data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehi

• If you are driving during extreme high ambient temperatures andidling for extended periods of time in gear, it is recommended to runthe A/C in the M

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL (IF EQUIPPED)Temperature conversion: To switch between Fahrenheit and Celsius, refer toOptional or Standard me

• : Distributes air through the instrument panel vents, floor vents,rear seat floor vents and de-mister vents.•: Distributes air through the floor ven

13. DUAL: Press to engage/disengage separate passenger sidetemperature control.14. Power: Press to activate/deactivate the climate control system.When

For maximum cooling performance:• Automatic operation:1. Press AUTO for full automatic operation.2. Do not override A/C or(recirculated air).3. Set th

REMOTE START CLIMATE OPERATION (IF EQUIPPED)The climate control system will condition the cabin temperature duringremote start based on the outside te

HEADLAMP CONTROLRotate the headlamp controlclockwise to the first position toturn on the parking lamps.Rotate clockwise to the secondpositionto also t

3. Turn the ignition switch to on and then back to off.4. Turn the headlamp control to the autolamp position. The headlampswill turn on.5. Wait the de

Daytime running lamps (DRL) (if equipped)Turns the headlamps on with a reduced output.To activate:• the ignition must be in the on position,• the head

Vertical aim adjustmentThe headlamps on your vehicle can only be vertically adjusted. Yourvehicle does not require horizontal aim adjustments.To adjus

limitations regarding 911 Assist and Traffic, directions andInformation privacy below). However, parties, such as lawenforcement, could combine the ED

TURN SIGNAL CONTROLThe turn signal lever does not mechanically lock in the upward ordownward position when activated. The turn signal control activati

To turn on the map lamps, press thelamp.The dome lamp turns on when:• any door is opened,• the instrument panel dimmer switch is rotated up until the

Replacing exterior bulbsCheck the operation of all the bulbs frequently.Function Numberof bulbsTrade numberHeadlamps 2 H13/9008Park/Turn lamp 2 3157NA

2. Using masking tape or a marker,make an alignment mark betweenone of the grille brackets and thevehicle radiator support to ensurecorrect grille ali

11. For the park or turn lamp bulb,remove the bulb by turning itcounterclockwise and pulling itstraight out.WARNING: Handle a halogen headlamp bulb ca

Replacing brake/tail/turn/back-up lamp bulbs (chassis cabs only)(if equipped)1. Make sure the headlamps are off.2. Remove the four screws and thelamp

Replacing fog lamp bulbs (if equipped)1. Make sure the headlamps are off.2. Remove the bulb socket from thefog lamp by turning itcounterclockwise.3. D

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the

TILT/TELESCOPE STEERING WHEELTo adjust the steering wheel:1. Pull the lever down to unlock thesteering column.2. While the lever is in the downpositio

OVERHEAD CONSOLE (IF EQUIPPED)The appearance of your vehicle’s overhead console will vary according toyour option package.Storage compartment (if equi