Ford CRAFTSMAN F-150 Bedienungsanleitung PDF herunterladen (Seite 24)

PROBLEMS AND SOLUTIONS GUIDE

K3033a-0920

IMPORTANT! If you experience a problem with your vehicle, first check the Problems and Solutions Guide below. If you still experience a

problem, please contact Power Wheels

Consumer Relations, toll-free at 1-800-348-0751 between 9 AM and 7 PM (EST) Monday through

Friday, and 11 AM - 5 PM (EST) Saturday. Or, contact your local Power Wheels

authorized service center. For the location nearest you,

please visit us on-line at www.powerwheels.com, or call 1-800-348-0751.

PROBLEM POSSIBLE CAUSE SOLUTION

Vehicle does not run Undercharged battery Charge the battery. A new battery should have been charged for at

least 18 hours before using the vehicle for the first time. After first-

time use, recharge the battery for at least 14 hours after each use.

Never charge the battery longer than 30 hours.

Check all connectors. Make sure the charger connector is plugged

into the battery connector, and that the charger is plugged into

the wall.

Make sure power flow to the wall outlet is “ON”.

Charger is not working There is no sure way to tell if your charger is working unless you

have a volt meter. If you suspect there is a problem with your

charger, contact your local Power Wheels

authorized service

center. They can test your charger for you.

Tripped thermal fuse Each Power Wheels

6 volt battery has a built-in thermal fuse.

A thermal fuse may “trip” and shut down operation of the vehicle

if the vehicle is overloaded or the driving conditions too severe.

Once a fuse has "tripped", remove your foot from the pedal and

wait 25 seconds before operating the vehicle again. To avoid

repeated automatic shutdowns, do not overload the vehicle by

exceeding the 65 lb. maximum weight capacity or by towing

anything behind the vehicle. Do not drive up hills or run into fixed

objects, which can cause the wheels to stop spinning while power

is still being supplied to the motors. If a thermal fuse continually

trips, contact your local Power Wheels

authorized service center.

Loose wire or loose connectors Check all wires and connectors. Make sure the motor harness

connector is plugged into the battery connector, and that there are

no loose wires around the motors.

Dead battery If your battery is old or if you have not followed Battery Care

instructions, your battery may be dead. If you are unsure whether

or not the battery is dead, you can have it tested at your local

Power Wheels

authorized service center.

Electrical switch damage The electrical switches can become corroded due to exposure to

water or moisture, or can jam due to loose dirt, sand or gravel.

Contact your local Power Wheels

authorized service center for

diagnosis and repair.

Motor damage Contact your local Power Wheels

authorized service center for

diagnosis and repair.

Vehicle was running but

suddenly stopped

Loose wire or loose connectors Check all wires and connectors. Make sure the motor harness

connector is plugged into the battery connector, and that there are

no loose wires around the motors.

Tripped thermal fuse Each Power Wheels

6 volt battery has a built-in thermal fuse. A

thermal fuse may "trip" and shut down operation of the vehicle

if the vehicle is overloaded or the driving conditions too severe.

Once a fuse has "tripped", remove your foot from the pedal and

wait 25 seconds before operating the vehicle again. To avoid

repeated automatic shutdowns, do not overload the vehicle by

exceeding the 65 lb. maximum weight capacity or by towing

anything behind the vehicle. Do not drive up hills or run into fixed

objects, which can cause the wheels to stop spinning while power

is still being supplied to the motors. If a thermal fuse continually

trips, contact your local Power Wheels

authorized service center.

1 2 ... 19 20 21 22 23 24 25 26 27 28

Kommentare zu diesen Handbüchern

Keine Kommentare

Ford CRAFTSMAN F-150 Bedienungsanleitung Seite 24

Kommentare zu diesen Handbüchern